Version=11113
Setting type=CNC controller settings

;----------------------------------------------------------------------------------------------------------------------------------------------------
;Vor Änderungen an dieser Datei muss Estlcam unbedingt geschlossen werden - sonst gehen die Änderungen verloren!
;Die "Steuerungselektronik" Liste der Grundeinstellungen setzt alles auf Standardwerte zurück - klicke Sie nach manuellen Änderungen nicht mehr an!
;----------------------------------------------------------------------------------------------------------------------------------------------------

Enabled=yes
Hardware=Uno
Firmware=E_328
Port=COM5

;Axis configuration
X steps rev=6400
Y steps rev=6400
Z steps rev=1600
X distance rev=45
Y distance rev=45
Z distance rev=4
X feedrate=83.333335876464844
Y feedrate=83.333335876464844
Z feedrate=20.833333969116211
X inertia=75
Y inertia=75
Z inertia=50
X inverted=no
Y inverted=yes
Z inverted=yes

Acceleration distance=10
Min feedrate=1.25
Fast Diagonal=no
Invert enable output=no
Switch enable output=no

Override oversampling=-1
Override pulse=999999999
Manual programming reset=no

Position X=0
Position Y=0
Position Z=0
Home offset X=0
Home offset Y=88178
Home offset Z=38000
Feedrate=50
RPM=20000
Last CNC file=500x250 Square
Last CNC line=825
Last CNC rotation=0
Balance message=yes

;Spindle configuration
RPM min=8000
RPM max=24000
RPM delay=0.5
PWM min=0
PWM max=100
PWM Frequency=0
Spindle output inverted=no

;Inputs
Input 1 name=Z-Home
Input 1 function=1
Input 1 inverted=yes
Input 1 pull-up=yes

Input 2 name=XYZ-Limits
Input 2 function=1
Input 2 inverted=yes
Input 2 pull-up=yes

Input 3 name=E-Stop-Input
Input 3 function=5
Input 3 inverted=yes
Input 3 pull-up=yes

Input 4 name=Probe-Input
Input 4 function=2
Input 4 inverted=no
Input 4 pull-up=yes

Input 5 name=Control-Fault
Input 5 function=3
Input 5 inverted=no
Input 5 pull-up=yes

Input 6 name=
Input 6 function=0
Input 6 inverted=no
Input 6 pull-up=yes

Input 7 name=X-Home
Input 7 function=1
Input 7 inverted=yes
Input 7 pull-up=yes

Input 8 name=Y-Home
Input 8 function=1
Input 8 inverted=yes
Input 8 pull-up=yes

Input 9 name=Input 9
Input 9 function=0
Input 9 inverted=no
Input 9 pull-up=yes

Input 10 name=Input 10
Input 10 function=0
Input 10 inverted=no
Input 10 pull-up=yes

Input 11 name=Input 11
Input 11 function=0
Input 11 inverted=no
Input 11 pull-up=yes

Input 12 name=Input 12
Input 12 function=0
Input 12 inverted=no
Input 12 pull-up=yes

Input 13 name=Input 13
Input 13 function=0
Input 13 inverted=no
Input 13 pull-up=yes

Input 14 name=Input 14
Input 14 function=0
Input 14 inverted=no
Input 14 pull-up=yes

Input 15 name=Input 15
Input 15 function=0
Input 15 inverted=no
Input 15 pull-up=yes

Input 16 name=Input 16
Input 16 function=0
Input 16 inverted=no
Input 16 pull-up=yes

;Outputs
Output 1 name=Output 1
Output 1 picture=img_flood

Output 2 name=Output 2
Output 2 picture=img_mist

Output 3 name=Output 3
Output 3 picture=img_vac

Output 4 name=Output 4
Output 4 picture=img_compressor

Output 5 name=Output 5
Output 5 picture=img_light

Output 6 name=Output 6
Output 6 picture=

Output 7 name=Output 7
Output 7 picture=

Output 8 name=Output 8
Output 8 picture=

;Homing
Auto home=no
Home switch location X=0
Home switch location Y=1
Home switch location Z=1
Homing speed=16.666666666666668
Homing probe speed=1.6666666666666667
Check step losses=no
Zero after homing=yes
Travel limits enabled=yes
Travel limit X=620
Travel limit Y=620
Travel limit Z=95
Deceleration distance=15
Park after homing=no
Park after controller start=no
Park after CNC program end=no
Park after M00 M01=no
Parking position X=0
Parking position Y=0
Parking position Z=0

;Tool sensor
Tool sensor probe speed=2.5
Tool sensor back up distance=20
Tool sensor fixed position=no
Tool sensor fixed position X=0
Tool sensor fixed position Y=0
Tool sensor fixed position Z=0
Tool sensor fixed Z=no
Tool sensor Z value=0

;Touch plate
Touch plate probe speed=4.166666666666667
Touch plate probe distance=20
Touch plate angle measurement distance=65
Touch plate margin X=6
Touch plate margin Y=6
Touch plate margin Z=9

;Keyboard
Keyboard enabled=yes
Key 0=104
Key 1=105
Key 2=102
Key 3=99
Key 4=98
Key 5=97
Key 6=100
Key 7=103
Key 8=33
Key 9=34
Key 10=38
Key 11=40
Key 12=39
Key 13=37
Key 14=113
Key 15=32
Key 16=50
Key 17=51
Key 18=52
Key 19=53
Key speed 0=2
Key speed 1=10
Key speed 2=25
Key speed 3=50
Key speed 4=100

;Gamepad
Gamepad enabled=no
Gamepad low speed=2
Gamepad high speed=100
Gamepad exponent=0
Gamepad sensitivity=2
Gamepad single axis=no
Gamepad beep=no

;External controls
Feed override knob enabled=no
Feed override knob min pos=13107
Feed override knob max pos=52429
Spindle override knob enabled=no
Spindle override knob min pos=13107
Spindle override knob max pos=52429
Jog wheel enabled=no
Jog wheel X inverted=no
Jog wheel Y inverted=no
Jog wheel Z inverted=no
Jog wheel coupled 1=yes
Jog wheel coupling factor 1=1:1
Jog wheel speed 1=10
Jog wheel coupled 2=yes
Jog wheel coupling factor 2=2:1
Jog wheel speed 2=50
Jog wheel coupled 3=yes
Jog wheel coupling factor 3=1:1
Jog wheel speed 3=100
Jog wheel coupled 4=no
Jog wheel coupling factor 4=1:1
Jog wheel speed 4=10
Jog wheel coupled 5=no
Jog wheel coupling factor 5=1:1
Jog wheel speed 5=50
Jog wheel coupled 6=no
Jog wheel coupling factor 6=1:1
Jog wheel speed 6=100
Jog wheel sensitivity=75
Joystick X enabled=no
Joystick Y enabled=no
Joystick Z enabled=no
Joystick X inverted=no
Joystick Y inverted=no
Joystick Z inverted=no
Joystick X center=50
Joystick Y center=50
Joystick Z center=50
Joystick X backlash=10
Joystick Y backlash=10
Joystick Z backlash=10
Joystick speed 1=100
Joystick speed 2=10
Joystick speed 3=20
Joystick speed 4=100
Joystick speed 5=100
Joystick speed 6=100
Joystick expo 1=60
Joystick expo 2=0
Joystick expo 3=0
Joystick expo 4=0
Joystick expo 5=0
Joystick expo 6=0
Joystick single axis 1=no
Joystick single axis 2=yes
Joystick single axis 3=yes
Joystick single axis 4=no
Joystick single axis 5=no
Joystick single axis 6=no
Joystick beep 1=yes
Joystick beep 2=yes
Joystick beep 3=yes
Joystick beep 4=no
Joystick beep 5=no
Joystick beep 6=no
Joystick sensitivity=5
Module=

Webcam application=
Webcam window margin left=0
Webcam window margin right=0
Webcam window margin top=0
Webcam window margin bottom=0
Webcam tool offset X=0
Webcam tool offset Y=0
Webcam tool offset Z=0
Webcam aligned to preview=no
;Misc
Back up distance=1
Surface scan speed=2
Touch mode=no

;Bootloader
Bootloader Baudrate=115200
Bootloader Reset_Time=10
Bootloader Wait_Time=500

Preset info=